Model

Specification

T-50A

T-50B

T-50C

T-50D

CH1

CH2

CH3

CH1

CH2

CH3

CH1

CH2

CH3

CH1

CH2

CH3

DC output voltage

5V

12V

-5V

5V

12V

-12V

5V

15V

-15V

5V

15V

24V

Output voltage error (Note2)

±2%

±5%

±5%

±2%

±5%

±5%

±2%

±5%

±5%

±2%

±6%

±6%

Rated output current

7A

1A

1A

5A

1A

1A

4A

1A

1A

3A

1A

1A

Output current range

0.6-7A

0.2-1A

0.2-1A

0.6-5A

0.2-1A

0.2-1A

0.6-4A

0.2-1A

0.2-1A

0.6-4A

0.2-2A

0.2-1A

Wave and noise(Note3)

100mV

100mV

100mV

100mV

100mV

100mV

100mV

100mV

100mV

50mV

120mV

120mV

Inlet stability(Note4)

±0.5%

±0.5%

±0.5

±0.5%

±0.5%

±0.5

±0.5%

±0.5%

±0.5

±0.5%

±1%

±1%

Load stability(Note5)

±1%

±4%

±4%

±1%

±4%

±4%

±1%

±4%

±4%

±1%

±5

±5%

DC output power

52W

49W

50W

51W

Efficiency

66%

69%

71%

72%

Adjustable range for DC voltage

CH1+10,-5%

CH1+10,-5%

CH1+10,-5%

CH1+10,-5%

AC input voltage range

85132VAC/170264VAC selected by switch 4763Hz;240370VDC

Input current

1.6A/115V 0.8A/230V

AC impulse current

Cold-start current 20A/115V 40A/230V

Leakage current

<0.5A/240VAC

Overload protection

105%150% TypePULSING HICCUP SHUTDOWN ;Reset auto recovery

Over-voltage protection

.

High-temperature protection

.

Temperature coefficient

±0.03%(050) ON+5V OUTPUT

Setup rise hold up time

200ms,50ms,16ms

Vibration

10500Hz,2G 3AXES 10min./1cycle,Period for 60min,Each axes

Withstand voltage

Input and output interval1.5KVAC,Input and enclosure1.5KVAC,Output and enclosure0.5KVAC

Isolation resistance

Input and output interval,Input and enclosure,Output and enclosure500VAC/100M Ohms

Working temperature and humidity

-10+60,20%90%RH

Store temperature and humidity

-20+85,10%95%RH

Overall dimension

159*97*38mm

Weight

0.54Kgs

Safety standards

Meet UL1012 requirement(Not apply for the mark)

EMC standards

Note:

1. The testing condition for the parameter above is:230VAC input, rated load,25 70%Rh,Humidity
2. Error,include the setting error, line stability and load stability.(Note:5)
3. Wave test:adoptingA12double wire for 20MHz,and 0.1uF&uF capacitor short-circuit for interrupting
4. Inlet voltage stability test: when is over load, the lowest voltage of inlet is representative to the highest voltage.
5. Load stability test: The load is from 0% to 100%,others 60%.
6. C2311must be knocked down.